A selection of replacement detectors for various mass spectrometers
Showing 1–20 of 25 results
-
£1,253.00ETP-14610
Electron Multiplier for AB Sciex API 2000
This electron multiplier is an off-axis detector by ETP specifically made for the Sciex API 2000 LC-MS quadrupole.
-
£2,189.00ETP-14222
Electron Multiplier for Agilent 7500 ICP-MS
The purpose of the dual-mode multiplier is to deliver both analogue and pulse-counting signals simultaneously to the detection electronics.
A “Gate” electrode is included so that the pulse counting section of the multiplier can be “gated off” to protect it from larger signal peaks.
-
£1,491.00ETP-14133
Electron Multiplier for Cameca 3F and 4F SIMS
This electron multiplier was developed specifically for quadrupole residual gas analyser (RGA) applications where compact design is combined with high sensitivity and simple operation.
-
£1,654.00ETP-14133H
Electron Multiplier for Cameca 5F and 6F (High Current) SIMS...
High current option. High linear dymanic range version – developed specifically for quadrupole residual gas analyser (RGA) applications where compact design is combined with high sensitivity and simple operation.
-
£1,461.00ETP-14824
Electron Multiplier for Comstock Mini-TOF
TOF detector with flat/orthogonal ion impact surfaces, narrow pulse width and a large dynamic range.
- Bakeable to 350°C
- Maximum sustained output current limit for linear operation of 5 micro amps.
- Available with the high current option by adding the suffix H to the part number. This increases the sustained output current limit for linear operation to 30 micro amps and decreases the internal resistance to 10% of the standard value.
-
£2,361.00ETP-14834H
Electron Multiplier for GBC OptiMass ICP-MS
TOF detector with flat/orthogonal ion impact surfaces, narrow pulse width and large dynamic range. Bakeable to 350°C.
High current, increasing the sustained output current limit for linear operation to 30 micro amps thus decreasing the internal resistance to 10% of the standard value.
-
£1,152.00ETP-14618
Electron Multiplier for HP / Agilent 5973 / 5975 GC-MSD (Mou...
This mount is compatible with ETP-14616 detector (no mount).
-
£1,171.00ETP-14617
Electron Multiplier for HP / Agilent 5973/5975 GC-MSD (Detec...
This detector (including mount) has been specifically developed to retrofit the Agilent Technologies 5973 / 5975 MSD. It incorporates a modular design to facilitate ease of replacement and includes additional innovations intended to enhance performance.
Suits Agilent / HP 5973 (without Triple Axis Detector) and Agilent 5975 MSDs (not 5975C)
* NOTE: If installing for a subsequent time, please purchase part ETP-14616 which includes both the detector only and re-use the mount. (The mount houses the HED (high energy dynode) which increases the energy of the ions and reduces multiplier contamination).
-
£988.00ETP-14616
Electron Multiplier for HP / Agilent 5973/5975 GC-MSD (Detec...
This detector (not including mount) has been specifically developed to retrofit the Agilent Technologies 5973 MSD / 5975. It incorporates a modular design to facilitate ease of replacement and includes additional innovations intended to enhance performance.
* NOTE: If installing for the first time, please purchase part ETP-14617 which includes both the detector and mount. The mount houses the HED (high energy dynode) which increases the energy of the ions and reduces multiplier contamination.
If installing having first installed part ETP-14617, the assembly can be re-used and this part installed.
-
£1,002.00ETP-14516
Electron Multiplier for HP 5971, 5972 & GCD GC-MSD
This detector has been specifically designed to retrofit HP 5971, 5972 and GCD GC-MSD systems.
Being completely self contained and plug compatible with the original equipment, it comes complete with an electrical lead set.
No special mounting assemblies or other hardware are required and installation or replacement of the multiplier takes about 5 minutes once the mass spectrometer is cooled and vented to atmosphere.
-
£1,654.00ETP-14140
Electron Multiplier for Infinicon Balzers SEV-217 SIMS
- Generic line-of-site analogue detector 88 mm long.
- Particle entry for magnetic sector instruments and other charged and neutral particle detection.
- Maximum sustained output current limit for linear operation of 10 micro amps.
- Unit is bakeable to 350°C.
-
£1,956.00ETP-14632
Electron Multiplier for Jeol K9 GC-MS
Replacement multiplier and mount for the Jeol K9 GC-MS.
-
£2,843.00ETP-14874
Electron Multiplier for Kratos AXIMA (Linear-High Dynamic Ra...
This TOF detectors has flat/orthogonal ion impact surfaces, narrow pulse width, large dynamic range and is bakeable to 350°C.
Maximum sustained output current limit for linear operation of 5 micro amps.
-
£1,633.00ETP-14820
Electron Multiplier for Kratos Kompact MALDI-TOF
This TOF detector offers the high dynamic range, pulse linearity and rapid recovery.
Innovations incorporated into these specialised detectors include thick-film capacitors to enhance linear response for large pulses, large active area (up to 20mm x 25mm) and 5000 volt conversion dynode operation for enhanced high-mass sensitivity.
Precision mounting arrangements are included with most models.
-
£1,517.00ETP-14143
Electron Multiplier for NU Instruments Nu Plasma ISO-RAD
This line-of-site analogue detector is 88 mm long, with a chimney mounted on input aperture, particle entry for magnetic sector.
-
£1,517.00ETP-14144
Electron Multiplier for NU Instruments Nu Plasma with filter...
This line-of-site analogue detector 88 is mm long.
Identical to the ETP-14143 without the input aperture chimney.
Particle entry for magnetic sector instruments and other charged and neutral particle detection.
Unit is bakeable to 350°C.
-
£2,573.00ETP-14217
Electron Multiplier for Perkin Elmer Sciex 9000 ICP-MS
The purpose of this dual-mode multiplier is to deliver both analogue and pulse-counting signals simultaneously to the detection electronics.
A “Gate” electrode is included so that the pulse counting section of the multiplier can be “gated off” to protect it from larger signal peaks.
-
£2,401.00ETP-14210
Electron Multiplier for Perkin Elmer Sciex ELAN 6000, ELAN 6...
The purpose of this dual-mode multiplier is to deliver both analogue and pulse-counting signals simultaneously to the detection electronics.
A “Gate” electrode is included so that the pulse counting section of the multiplier can be “gated off” to protect it from larger signal peaks.
-
£1,990.00ETP-14823H
Electron Multiplier for Sensar / Larson-Davis TOF 2000
This TOF detectors flat/orthogonal ion impact surfaces, narrow pulse width and large dynamic range.
- Bakeable to 350°C.
- High current, thus increasing the sustained output current limit for linear operation to 30 micro amps and decreases the internal resistance to 10% of the standard value.
-
£1,164.00ETP-14533
Electron Multiplier for Shimadzu QP 5000 GC-MS
This detector is specifically designed for the QP5000 GC-MS.
The ETP-14533 is a direct “plug-in” replacement electron multiplier for the QP5000 mass spectrometer and is fully compatible with the Shimadzu hardware and software.
There are three electrical connections to be made to install – electrical connections are made via the three pins extending from the base of the multiplier.
There are three connection pins, 1) high voltage, 2) shield and 3) signal output (Ground is connected via the mounting bracket).
